Payment & Shipping Terms:
|CAS register number:||10161-33-8||Appearance:||Pale Yellow Or Yellow Crystalline Powder;|
HPLC Trenbolone Steroids
Trenbolone Enanthate benefits:
• Increased muscle mass in short period of time;
• Strength increase almost instantly;
• Vascularity increases by it eliminating unnecessary water weight;
• Sheds body fat while preserving muscle;
• Increase in protein synthesis allowing body to use more that is consumed;
• Muscle will repair faster and you’ll be able to train harder & longer;
• Expansion of muscle fibers giving muscle ability for more growth;
• Facilitate an increase in free testosterone within the body;
• Does not aromatize.
|Purity:||99.46% by HPLC|
|Appearance:||Pale yellow or yellow crystalline powder|
|Minimum order quantity:||$80 / 10 grams|
|Payment term:||Money Gram;Western union;Bitcoin;Bank Transfer|
Tren Enan is a favorite of bodybuilders and athletes in other sports due to the fact it has both cutting and bulking properties. Let’s get into the benefits of it’s use for both cycles. When bodybuilders and athletes run off-season bulking cycles the use of Tren Enan will help promote lean muscle tissue growth. The bonus is that it will happen in a short amount of time. Those who use this steroid for bulking like the effects because the weight that is gained is clean mas rather than water retention which can be felt with the use of other anabolics during a bulking phase. Of course, we must remind you that no steroid, not even Tren Enan will do any good to your body during a bulking cycle if you aren’t eating enough to help those muscles grow.
For cutting cycles, there is not a single steroid out there that can be as beneficial as Trenbolone. The Enan version when used for cutting will accelerate the fat burning process and even help people get over that hump or plateau that is often felt after dieting and/or working out for longer periods of time. When cutting, the body will start to naturally rely on muscle for fuel. But with the use of Tren Enan during your cutting cycle, you will preserve lean muscle rather than burn it for fuel. Towards the end of your cycle you may begin to feel fatigued but Tren Enan will help cut the fat at the end of the cycle and get you to the end with added endurance.
Tren Enan is the longer ester version of Tren that has a slow absorption rate and a half-life of ten to twelve days. This means there is a reduced peaking time and a longer period of time to be eliminated from your system. Because of this, Tren Enan may cause fewer side effects and require less frequent injections. For example, if you plan on taking 500mg per week, you can split the dosages in half and inject twice per week at 250mg per injection. With the acetate version, users typically need to inject every other day (EOD).
Beginner and Intermediate users typically inject between 200-400mg per week. Those with more steroid experience may increase the dose and inject between 500-800mg per week. Keep in mind that higher doses of Tren Enan will increase your chances for the onset of negative side effects which at times can be very harsh.
Before the injection is important to prepare the drug itself. The presence of steroids with a concentration of 250 mg / ml would be the best option. Thus, the athlete will be able to more accurately calculate the required dose in compliance with all recommendations of the cycle. Preparation for injections is carried out in the following steps:
Before injecting the steroid, it is suggested to rub the bottle in between both hands to warm the steroid. Once heated, the steroid is ready to inject. It is important to note that injections are performed exclusively intramuscularly. The best areas to inject are the upper part of the thigh, shoulder or glutes. It is crucial to never inject in the same area twice. Always rotate your injections to allow time for the site to heal. When injecting in any of the areas mentioned above, do so without flexing your muscles because this makes it harder for the pin to go through the muscle.
To get more comfortable with self-injections, some suggest standing in front of a mirror. This will allow you to see the exact spot you are going to inject. It will also make you more comfortable with the motion of slowing pushing the solution into the muscle. Practice makes perfect.
Contact Person: Gavin Lee